Formación e Investigación en BIM – LÍNEA 1
Comunicación 1.3 – MANUAL DE INTERCAMBIO DE INFORMACIÓN GEOTÉCNICA: HACIA UN CONSENSO NACIONAL BASADO EN OPENBIM
Autores: Martínez Ibáñez, Víctor; Arnal Palacios, Christian; Lledó Fuster, Francisco Javier; Garrido De La Torre, María Elvira; Delgado Vendrell, David
Comunicación 1.2 – COMPARACIÓN ENTRE EL DISEÑO TRADICIONAL Y EL DISEÑO GENERATIVO EN BIM PARA EL TRATAMIENTO SECUNDARIO DE UNA EDAR
Autores: Yanza-Pérez, Christian Andrés; Pacheco-Rodríguez, Christian Miguel; Álvarez-Rojas, Mailen Stephany; Cortés-Pérez, Juan Pedro; Núñez-Fernández, Mario.
Comunicación 1.1 – INTEGRACIÓN GIS-BIM MEDIANTE FORMATO ABIERTO IFC: EL CASO DE ÉXITO DEL ÁREA METROPOLITANA DE BARCELONA Y SU IMPACTO EN LA NORMALIZACIÓN
Autores: Monteagudo Gómez, Montserrat; Duran Sancho, Maria.
Comunicación 1.3
MANUAL DE INTERCAMBIO DE INFORMACIÓN GEOTÉCNICA: HACIA UN CONSENSO NACIONAL BASADO EN OPENBIM
Autores: Martínez Ibáñez, Víctor; Arnal Palacios, Christian; Lledó Fuster, Francisco Javier; Garrido De La Torre, María Elvira; Delgado Vendrell, David
Abstract
In Spain, there are currently no specific standards, guidelines, or technical references that define how information related to geotechnical engineering should be produced and exchanged. To address this gap, the project “Geotechnical Information Exchange Manual” was launched in December 2025 as a joint initiative of the Universitat Politècnica de València and buildingSMART Spain, with the participation of a broad representation of stakeholders from the national geotechnical sector. The main objective of the project is to reach a consensus on how geological and geotechnical information should be produced and exchanged using open standards. This paper presents the main advances achieved to date, including: (1) a review of national and international guidelines, norms, and standards; (2) the identification and analysis of BIM requirements related to ground engineering in public procurement processes for projects and construction works; and (3) the identification of parameters commonly used in geotechnical design and their correspondence in BIM classification systems and in IFC.
Keywords: BIM, OpenBIM, IFC, geotechnical engineering, geological information, information exchange, standardization, BIM requirements, public procurement, interoperability
Resumen
Actualmente, en España no existen normas, guías ni recomendaciones técnicas específicas que definan cómo debe producirse e intercambiarse la información relacionada con la ingeniería geotécnica. Para dar respuesta a esta carencia, en diciembre de 2025 se inició el proyecto “Manual de intercambio de información geotécnica” como una iniciativa conjunta de la Universitat Politècnica de València y buildingSMART España, que cuenta con la participación de una amplia representación de agentes del sector geotécnico nacional. El objetivo es alcanzar un consenso sobre cómo producir e intercambiar la información geológica y geotécnica mediante el uso de estándares abiertos. En esta comunicación se presentan los principales avances alcanzados hasta el momento, que incluyen: (1) la revisión de guías, normas y estándares nacionales e internacionales; (2) la identificación y análisis de los requisitos BIM vinculados a la ingeniería del terreno en la contratación pública de proyectos y obras; y (3) la identificación de los parámetros de uso habitual en el proyecto geotécnico y su equivalencia en sistemas de clasificación BIM y en IFC.
Palabras clave: BIM, OpenBIM, IFC, ingeniería geotécnica, información geológica, intercambio de información, estandarización, requisitos BIM, contratación pública, interoperabilidad
Comunicación 1.2
COMPARACIÓN ENTRE EL DISEÑO TRADICIONAL Y EL DISEÑO GENERATIVO EN BIM PARA EL TRATAMIENTO SECUNDARIO DE UNA EDAR
Autores: Yanza-Pérez, Christian Andrés; Pacheco-Rodríguez, Christian Miguel; Álvarez-Rojas, Mailen Stephany; Cortés-Pérez, Juan Pedro; Núñez-Fernández, Mario.
Abstract
This communication presents how Generative Design (GD) integrated into BIM can complement the traditional design of the Secondary Treatment (ST) of a wastewater treatment plant (WWTP) based on activated sludge and extended aeration for small communities. Preliminary sizing ranges for the biological reactor (BR) and secondary clarifier (SC) are defined based on technical literature. Together with design requirements (population equivalent, water supply, and biological parameters such as BOD and MLSS), these ranges enable the workflow to be parameterized in Dynamo and allow GD constraints and objectives to be defined. GD applies multi-objective optimization and produces a set of efficient (non-dominated) solutions, with associated dimensions that can be exported to BIM software as geometric and quantifiable alternatives. Finally, the solutions are compared with the ST of a real WWTP (BIM model), identifying early-stage benefits such as: reduced design time, a broader view of alternatives, potential for investment reduction, and traceable support for decision-making.
Keywords: BIM, Generative Design, WWTP, Multi-objective optimization, Dynamo, Parametrization.
Resumen
En esta comunicación se presenta cómo el Diseño Generativo (GD) integrado en BIM puede complementar el diseño tradicional del Tratamiento Secundario (TS) de una Estación Depuradora de Agua Residual (EDAR) de fangos activos y aireación prolongada para pequeñas poblaciones. Se definen rangos de predimensionamiento del Reactor Biológico (RB) y Decantador Secundario (DS) a partir de bibliografía técnica. Junto con los requisitos de diseño (población equivalente, dotación y parámetros biológicos como DBO y MLSS), estos rangos permiten parametrizar el flujo en Dynamo y definir las restricciones y objetivos del GD. El GD aplica optimización multiobjetivo y produce un conjunto de soluciones eficientes (no dominadas), con dimensiones asociadas y exportables a un software BIM como alternativas geométricas y cuantificables. Finalmente, las soluciones se contrastan con el TS de una EDAR real (modelo BIM) identificando en fases tempranas beneficios como: reducción de tiempo de diseño, visión ampliada de alternativas, potencial de reducción de inversión y soporte trazable en la toma de decisiones.
Palabras clave: BIM, Diseño Generativo, EDAR, Optimización multiobjetivo, Dynamo, Parametrización.
Comunicación 1.1
INTEGRACIÓN GIS-BIM MEDIANTE FORMATO ABIERTO IFC: EL CASO DE ÉXITO DEL ÁREA METROPOLITANA DE BARCELONA Y SU IMPACTO EN LA NORMALIZACIÓN
Autores: Monteagudo Gómez, Montserrat; Duran Sancho, Maria.
Abstract
The Metropolitan Area of Barcelona (AMB) published the BIM models of the metropolitan territory in IFC format in March 2023, which were developed from the 1:1,000 Metropolitan Topographic Map.
This product made possible, for the first time, to integrate a continuous supramunicipal 3D cartography into the BIM methodology through an open and interoperable format, enabling professionals in the AECO sector to incorporate building and infrastructure projects with territorial continuity. The open publication through the Cartography Geoportal generated strong interest among different technical profiles from public, private, and academic sectors interested in the connection between GIS and BIM. The impact of the product was analysed from usage metrics.
Currently, the AMB is working on the standardization of GIS–BIM integration at regional, national, and international levels, participating in UNE and ISO standards (chairing Subcommittee 2 of CTN-332 on GIS–BIM information exchange), coordinating the Working Group for the definition of the Urban Topographic Base specification and its integration into BIM (national scope), and leading the Local Topographic Reference – BIM Working Group (regional scope). The IFC models are also being further developed toward new schemas (IFC4.3) and the use of BIM As-Built models to update official cartography, in line with the BIM Plan for public contracting.
Keywords: GIS, BIM, IFC, Cartography Geoportal, Cartography, Interoperability, Normalization, Automation, Digital Twin, Digital Transformation
Resumen
El Área Metropolitana de Barcelona (AMB) publicó en marzo de 2023 los Modelos BIM del territorio metropolitano en IFC, elaborados a partir del Mapa Topográfico Metropolitano 1:1.000.
Este producto permitió integrar por primera vez una cartografía supramunicipal continua 3D, dentro de la metodología BIM mediante un formato abierto e interoperable, facilitando a los profesionales del sector AECO la incorporación de proyectos de edificación e infraestructuras con continuidad territorial. La publicación abierta en el Geoportal de Cartografía despertó un gran interés entre diferentes perfiles técnicos de los ámbitos público, privado y académico, interesados en la conexión entre GIS y BIM. A partir de las métricas de uso se analizó el impacto del producto.
Actualmente, el AMB trabaja en la normalización de la integración GIS-BIM a nivel autonómico, nacional e internacional, participando en normas UNE e ISO (Presidiendo el Subcomité 2 del CTN-332 sobre intercambio de información GIS-BIM), coordinando el Grupo de trabajo para la definición de la especificación de la Base Topográfica Urbana y su integración en BIM (ámbito estatal), liderando el GT Referencial Topográfico Local – BIM (ámbito autonómico). También se están evolucionando los modelos IFC hacia nuevos esquemas (IFC4.3) y el uso de modelos As-Built BIM para actualizar la cartografía oficial, en línea con el Plan BIM en la contratación pública.
Palabras clave: GIS, BIM, IFC, Geoportal Cartografía, Cartografía, Interoperabilidad, Normalización, Automatización, Gemelo Digital, Transformación Digital.